View IA6008-FA22A_1252478.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IA6008-FA22A
Contact image sensor heads
Color image sensor heads for multi-function
IA6008-FA22A
"Color contact image sensor" with optical system intended for Flatbed scanning. Optical technology established for sheet-feed scanning has been further advanced for Flatbed scanning.
Applications Image sensor heads device for multiple function facsimiles such as color scanner and multiple function printer.
Features 1) Signal amplifier is built in to the image sensor IC in order to increase immunity to external noise. 2) Additionally, newly developed analog memory circuit and realizes high speed scanning. 3) The LED light source is mounted on the same substrate as the sensor chip which makes it possible to package the device with lighter weight and an extremely small size. 4) With the proprietary prism, the output signal is maintained uniformly. 5) The ceramic substrate is used for excellent dimensional accuracy and thermal stability.
External dimensions (Unit : mm)
236 0.5 2- 1.5x2 Oval Hole D4MIN Scanning line
14 0.2
212 (Effective Reading Width) Effective 1st bit
11.9 0.8
9.4
0.524 0.1
Dimension of frame reference surface level.
14 0.2
+ 2- 1.5 D4MIN
+
MAX 2.35
2-
- 3 + 0 0.0 5
1mm pitch 12pin
6.7
No.12 Center of FCC
No.1 13.8
Pin No. No.1 No.2 No.3 No.4 No.5 No.6
Signal Ao GND GND VDD GND SP
Pin No. No.7 No.8 No.9 No.10 No.11 No.12
Signal CLK V-LED B-GND G-GND R-GND F-GND
17.5
1/4
IA6008-FA22A
Contact image sensor heads
Characteristics
Parameter Effective scanning width Primary scan dot density Total dot number Power supply voltage Scanning speed Clock frequency Maximum dynamic range Minimum dynamic range Dark output Operating temperature Symbol - - - VDD SLT CLK VRmax VRmim. Vod - Typ. 212 600 5160 5 6.6 1.25 0.5 0.25 1.73 + 0.45 - 5 to 45 Unit mm dpi dots V ms / line MHz V V V C
Analog signals are output at the double rate of clock frequency.
Pin assignments
No. 1 2 3 4 5 6 7 8 9 10 11 12 Circuit AO GND GND VDD GND SP CLK V-LED B-GND G-GND R-GND F-GND I/O O I I I I I I I I I I I Function
Analog output Ground Ground Power supply
Ground Start pulse Clock LED power supply BLUE LED ground GREEN LED ground RED LED ground Frame ground
2/4
IA6008-FA22A
Contact image sensor heads
Timing chart (a) CLK Timing Chart
1/fCLK twCLK twCLK
CLK
tSETUP tHOLD
SP
ts
Ao
1pixel 2pixel
(b) Data Output Timing Chart After turning on the SP pulse, the analog output starts from the setting up point of 27 clock pulse.
1
2
3
26
27
28
29
CLK SP Ao
Note) The CLK section area which is over the effective pixel numbers (Output blank part) cannot be used as the analog Output standard level.
3/4
IA6008-FA22A
Contact image sensor heads
Equivalent circuit
VDD
1Fx2 1 5160 680ohm 1F 360ohm
GND
SP
ANALOG MEMORY CIRCUIT
CLK
VDD VREF
AO VLED
RGND GGND BGND F-GND
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.0

▲Up To Search▲

Price & Availability of IA6008-FA22A

	To Download IA6008-FA22A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .